Pics Official 1911 Photo Thread

[STILLinTheWest]

Rock island 1911

 

[Jimi Jah]

I have a Springfield mil spec 45, a target 9mm, a GSG .22 and EMP.

 

[Malibu]

I have a Springfield mil spec 45, a target 9mm, a GSG .22 and EMP.

My SA 9mm Target turned out good after some mods like a RDS, beveled sharp edges, bead blast finish, etc.

 

[Colt1911]

1950's Colt Commercial. Resto Mod by Dave at Evolution Armory.

 

[GeeQ87]

Updated sights on the Citadel. Nighthawk good bead and 10-8 rear.

 

[SDDAVE56]

Colt WWI


SA Mil Spec


Another Colt

 

[Sparky11]

Springfield EMP 3in 9mm ... Best gun I have!!!

 

[DesertLefty]

+1 for the EMP

 

[WGWaifus]

Waiting on my first 1911 to get out of gun jail. Been wanting a 1911 for years and finally got the opportunity to get my hands on one!

 

[slocookie]

Here’s a full house custom 6” 9mm Stainless. Started out as a Springfield Loaded 9mm stainless.
Build Sheet

• Springfield Armory Stainless 1911-A1 Frame
• Caspian 6” Long Slide
• Kart 9mm 6” Barrel
• Harrison Design Extreme Thumb Safety
• Harrison Design Extreme Slide Catch
• Harrison Design Extreme Mag Catch
• Harrison Design Extreme Trigger
• Harrison Design Extreme Firing Pin Stop
• Harrison Design Ejector
• Harrison Design Extreme Extractor
• Harrison Design Extreme Firing Pin Stop
• EGW Thick Bushing
• EGW Long Nose Bushing
• Extreme Shooters Ignition Set
• Stan Chen Magwell/MSH
• Wilson Combat BTGS
• Trijicon RMR Mounting Plate

Work Performed

• Tri-Cut Slide
• “Diamond Plate” Flat Top
• “Diamond Plate” Rear Serrations
• RMR Cut
• Ball Cuts to match frame
• Heavy Bevel bottom of slide
• Frame to slide fit
• Fit Kart Barrel to Slide
• Fit Firing Pin Stop
• Flush Cut Slide Stop Pin
• Reverse Crown Slide Stop Pin Hole
• Fit Slide Stop
• Soften Slide Stop and Thumb Safety sharp edges
• Fit/Blend/Re-contour thumb safety to match frame radius
• Fit/Blend Grip Safety
• Fit/Blend Chen Magwell/MSH
• High Cut Trigger Guard
• Checker front strap 25 LPI
• Fit and tune ejector
• Fit Extractor
• Blend rear of slide/extractor/ejector
• Fit Oversized Trigger
• 2.5 LB Trigger Job
• Highfigure Grips Spalted Maple
• Soft Satin Bead Blast Finish

Ooof, I just found my next project

 

[SteamedHams]

Picked up 2 more CMP 1911s. Both are service grade mixmasters with GI replacement slides contracted to IMI. One of them is a Colt frame, and the other one an lthaca frame. As luck would have it, the first CMP 1911 I got a few years ago was a Remington Rand with an Ithaca slide; I swapped that slide over so that I can at least have an all-Ithaca gun even if it’s not matching.

 

[shooterMcGavin]

Just a few

 

[Deleted member 769]

Jim Boland 38 super

 

[Hit Factor]

These are my USPSA Single Stack guns:



I couldn’t decide, so I got one of each.

 

[Striker777]

1987 1/2 NIB

 

[SLORNR]

Unicorn Rogers Precision on a Colt Series 70

 

[SLORNR]

Larry Vickers Built 1911 on a WC Slide and Frame Kit

 

[SLORNR]

MEUSOC Gen 1 Clone Correct by Sams Custom Gunworks

 

[rfgCA]

 

[damngato]